For quick assistance, Call Brother Printer Support Number @ :

All posts by Harley Thomson

For quick assistance, Call Brother Printer Support Number @ :

09Dec/19

Brother MFC-9560CDW Wireless Setup | Get Easy and Quick Guidance

The Brother MFC-9560CDW is a powerful color laser printer that is ideal for office or small workgroups. With its fast printing, wireless networking, and outstanding color output, this printer can give you the best result. Thus, you can learn how to perform a Brother MFC-9560CDW wireless setup in the following section. 

Brother MFC-9560CDW Wireless Setup: Step by Step Instructions

Without further ado, follow the given steps thoroughly to initiate the brother mfc-9560cdw wireless setup process.

Step 1- Unbox your Printer

At first, remove the Brother printer from its box and check the components. It should contain an AC power cord, Drum Unit, Waste toner box, Belt Unit, and a Telephone Line Cord. 

Thereafter, remove the tape from the outside of the machine. Then, open the MP tray and take out the Plastic sheet from it as well. After that, close the MP tray.

Next, press and hold the cover release button to open the front cover. Then, remove the silica gel packs from inside the device. 

Next, press the green handle of the drum unit and take it out. Then, remove the 4 orange stickers from it and put it firmly back inside the machine. Finally, close the cover. 

Step 2-  Load Paper in Paper Tray

Next, remove the paper tray from the machine. Ensure that the paper guides are properly adjusted according to the paper size that you are using. 

Then, put the paper tray inside the machine and place it back into the printer. Now, connect the printer’s cables to the power supply and turn it on by pressing the Power button. 

Step 3- Set the Time Zone

Now, the printer will automatically display the time. However, if you set the station ID, the time zone will automatically be added to each sent fax.

Press the Menu, 2, 0, 1 key together. Then enter the last two digits of the year on the dial pad and press the Enter key. The same rule should be applied on Month and date.

Type the time in 24 hrs format on the dial pad and hit the Enter key. Press the Stop or Exit key.

Step 4- Choose the Connection Type

Finally, you need to configure your printer for wireless settings. Thus, follow the steps below to do so. 

  1. On the Brother MFC-9560CDW printer, press menu after that press 7. After that, press 0 to select the Network Reset.  Then, twice press 1 to accept the changes.
  2. Again, press the Menu button and select Network from the list of options. Next, use the arrow keys to navigate and select WLAN by pressing the Ok button. 
  3. When the ‘WLAN Enable?’ message pops up on the display, select Yes by pressing the 1 button on the numpad. 
  4. Now, the printer will search for available SSID. In case, lots of SSID will available on the screen, press the up or down arrow to select the SSID that you want to connect to.
  5. Thereafter, enter the password of that network by using the numpad of the printer device. After this, the printer will confirm the credentials and connect to the Wi-Fi network. 

Now, you can try to print a test page to check whether you are able to use your printer or not. 

Final Words 

Brother MFC-9560CDW wireless setup is quite simple and an easy process. Thus, make sure that you have gone through the above instructions very carefully. Thereafter, try to print a test page to check whether you are able to print wirelessly or not. 

07Dec/19

Brother DCP-L2540DW Wireless Setup | Quick Installation Guide

Brother DCP-L2540DW Wireless Setup

Brother DCP-L2540DW has a lot of different features to offer. Thus, it is necessary to properly set up this device to enjoy optimal performance. Accordingly, you can either set it up using a wired connection or a wireless connection. Hence, go through the following section to setup Brother DCP-L2540DW printer wirelessly. 

How to Setup Brother DCP-L2540DW Wirelessly in a Few Easy Steps 

In this section, we are going to list out the different methods to setup your wireless printer. Thus, read them carefully and execute these steps as instructed to complete the wireless setup in no time. 

Method 1 – Using Printer’s Control Panel 

The best way to setup your wireless Brother DCP-L2540DW printer is by using its control panel. Thus, go through the steps below to do so. 

  • Turn on your printer and go to its Menu. Here, use the arrow keys to navigate and select Network from the options. Thereafter, go and select WLAN. 
  • Here, launch the Wireless Setup Wizard and enable WLAN if prompted. Thus, choose Yes if a pop-up menu appears. 
  • Now, the printer will search for available wireless connections. 
  • Select your network from the list and connect to it by entering its Security Key. 
  • Finally, install the printer driver on your computer and try to print a test page wirelessly. Check if you are able to print over the network or not. 

Method 2 – Using Printer Driver Software 

Alternatively, you can setup your Brother DCP-L2540DW printer wirelessly through its printer driver software. All printers come with their own installation discs. If you cannot find it, you can easily download it from Brother’s official website. 

Thereafter, follow the steps given below. 

  1. Run the installer file for the Printer driver software. Next, choose your printer’s model from the list and click on Next. 
  2. Here, choose the type of connection that you want to set up. In this case, choose Wireless Setup and follow the on-screen instructions. 
  3. Thereafter, connect your printer to the computer using a USB cable or LAN cable. After that, connect the printer to your Wi-Fi network and enter its password. Follow the rest of the instructions to complete the installation process. 

Finally, disconnect the cables from your computer and try to print a test page from your computer. Check if the green LED is turned on for a successful wireless connection. 

Conclusion 

Hopefully, you should be able to set up your Brother DCP-L2540DW printer over a wireless network by following the above steps. If you are having issues while doing the same, then you need to consult a professional technician to help you with the same. They will either do it for you or guide you through the process.

07Dec/19

How to Setup a Brother HL-L2350DW on a Wireless Network

Brother HL-L2350DW Wi-Fi Setup

The Brother HL-L2350DW all-in-one printer is a popular model that offers some really good features. The most helpful feature of this printer is the wireless connection feature. This will allow you to avoid all the problems related to a wired connection. Thus, you need to learn how to do brother hl-l2350dw wifi setup before using this feature.

Easy Ways to Setup Brother HL-L2350DW over a Wireless Network 

Here, we have provided easy step by step instructions to help you set up your wireless printer. Hence, go through them carefully. You can carry out the setup procedure by following any one of the following methods.  

Method 1 – Using Printer’s Control Panel 

The most basic way to setup your Brother HL-L2350DW wirelessly is through its control panel. Therefore, follow the steps given below to do so. 

  • Turn on your printer and go to the control panel. Now, use the arrow keys to navigate and select the Network option. Thereafter, press the OK button to open it 
  • Then, go to the WLAN option and click the OK button once again. Here, look for the Wireless Network Wizard and launch it. 
  • Now, you should get a prompt asking to “WLAN Enable?”. Simply choose yes to enable it. 
  • After that, your printer will start searching for the available network. Thus, select your network from the list and press the OK button to go to the next screen. 
  • Thereafter, enter the password for the network and finish the installation process. Next, go to the official website of Brother and download the printer driver from there. Install the printer driver to complete the setup procedure. 

After you have completed the setup, make sure to restart both the devices. Now, print a test page to check if the problem has been resolved or not. 

Method 2 – Using Windows Control Panel 

Alternatively, you can set up the Brother HL-L2350DW printer wirelessly by connecting it directly to the computer. After that, you can set it up using the Control panel. To do this, follow the steps given below. 

  1. First, click on the Start button and type ‘control’ in the text field. Subsequently, press enter to open the Control Panel. 
  2. Here. go to “Hardware and Sound” and select “Device and Printer” from the list. 
  3. From there, go to the “Add a printer” option and choose “Add Network/Wireless printer”.  
  4. Next, make sure that your printer’s Wi-Fi connection is on. Thereafter, choose your printer’s model from the list and click on “Next”. 
  5. Finally, follow the rest of the instructions to complete the installation process. 

After this, you can easily disconnect the cable from the printer and start using your printer normally. 

Conclusion 

By now, you should be able to easily complete the brother hl-l2350dw wifi setup. If you are having problems with getting it to work, then you may have to get in touch with Technical assistance. They will be able to help you out by either doing it for you or guiding you through the process correctly.  

07Dec/19

Setup Brother HL-3140CW on a Wireless Network

Brother HL-3140CW Wireless Setup

The Brother HL-3140CW is a compact and easy-to-use printer that is perfect for basic usage. It is efficient and can provide savings in terms of ink usage and energy consumption. Furthermore, it supports both wireless and wired connections. Thus, we will show how you can perform a Brother HL-3140CW wireless setup in the following section. 

Step by Step Methods for Brother HL-3140CW Wireless Setup 

Now we are going to discuss the exact steps that are needed to complete the wireless setup of your printer. Thus, go through each of the following steps very carefully. 

Step 1 – Configuring Wireless Settings 

First, you need to configure the wireless settings of your printer from its Control Panel. Thereafter, follow the instructions below to do so. 

 

  • First, turn on your printer and go to its LCD display. Here, press the Menu button from the panel. 
  • Now, use the Up/Down arrow keys to navigate and select the Network option from the list. You can select the option by pressing the Ok button. 
  • After that, find and select the WLAN option and again, press the OK button. 
  • Now, look for the Wireless Setup Wizard option and launch it by pressing Ok. 
  • After that, you will get a prompt with the “WLAN Enable?” message in it. Select the Yes option and continue with the setup process. 
  • Now, you will get to see a list of all the available wireless network access points that you can connect to. Find your router’s SSID and press the Ok button to continue. 
  • Finally, enter the password using the numpads and finish the setup process. Thereafter, go to the next step given below. 

 

Step 2 – Install Printer Driver Software 

After you have established a wireless connection on your printer, you need to install the printer driver software. Thus, go to the official website of Brother printer and search for the driver software for Brother HL-3140CW printer. 

Next, follow the instructions below to complete the installation process. 

  1. Run the installed file as an Administrator and choose your model of the printer from the list of options. 
  2. After this, select ‘Wireless Connection’ and continue with the setup procedure. Now, take a USB or a LAN cable and connect your printer to the computer. 
  3. Thereafter, choose the cable connection you used to connect the printer and carry on with the setup process. 
  4. Now, similar to the previous Step, it will again search for available networks to connect to. Thus, select your router’s SSID and enter its password. 
  5. Finally, finish the installation procedure and you will be able to start using your printer wirelessly. 

Conclusion 

Here, we have provided an easy step by step guide to help you perform a Brother HL-3140CW wireless setup. Hence, ensure that you have successfully followed all the instructions provided above. If you are unable to print wirelessly, then it might be your hardware’s fault or your own fault. Thus, you can contact Technical assistance in case you need some real-time help. 

07Dec/19

Brother MFC 225CW Wireless Setup : A Quick Guide

Brother MFC 225CW Wireless Setup

Brother MFC 225CW is one of the most purchased wireless printers. It is an all-in-one printer that has some unique features. Furthermore, it comes with a memory card slot so that you can print out photos without using a computer. With this printer, you can scan, copy, print and fax documents efficiently. You can also use the printer wirelessly. If you have recently bought this printer, then you need to know how to setup Brother MFC 225CW on a wireless network. 

How to Setup a Brother MFC 225CW Wireless Printer

Here, we are going to discuss how to set up the printer by configuring the wireless settings of the printer. Thereafter, we will go on to install the printer driver software in your computer system. 

Method 1: Configure Wireless Settings

Before following this method, you need to note down the Router’s network name (SSID) and its password. Thus, follow the instructions as given in the below section. 

  1. Go to your printer and tap on the “Menu” button near the LCD display. Now, press the “5” number key to choose the “Network” option.
  2. For “WLAN”, press the “2” number key. Now, the “WLAN Enable?” message will pop up on the screen. 
  3. Press the “1” number key to accept the message. Now, you have to launch the Wireless Setup wizard. 
  4. Now, the printer will start to look for all available SSIDs. Thereafter, use the scroll up and down keys to select your SSID from the list and press the Ok button. 
  5. Now, put the Password using the dial pads to select the numbers and letters. Use the left and right arrow keys to choose the letter and numbers. 
  • For example, you need to tap on the number “2” once if you want to write the letter “a”. Press the number key 3 four times to put the number 3. 
  1. Then, tap on the “OK” button after entering the password and press the number key “1” for “Yes” to apply the changes that you have made. 
  2. The printer will now try to establish a connection with the wireless network using the information that you have given. 
  3. The “Connected” message will pop-up on the screen if you successfully connect the printer and the network. 

If you have done all the steps correctly, you will be able to see a Connected successfully pop-up. Thereafter, go to the next step for configuring the same on your computer device. 

Method 2: Install the Printer Driver and Software 

If you are done with the wireless setup, you need to now install the drivers and software. Make sure that there are no external devices connected to your computer. If they are, simply remove them. 

Also, disable all firewalls and other related software. Thereafter, follow the steps given below. 

  1. Insert the CD-ROM that came with the printer into the CD-ROM drive. If you have misplaced it, you can also download the printer driver software from Brother’s official website. Do not forget to select your model as different models have different printer drivers. 
  2. Now, run the installer and select your printer from the options. Tap on the “Install MFL-Pro Suite” option. Click on “Yes” on the License Agreements in the “Installation Page.”
  3. Now, select the “Wireless Network Connection” and then tap on the “Next” button.
  4. Go to the “Wireless settings checked and confirmed” box and make sure it is checked. Tap on the “Next” button.
  5. Now, the installation of the Brother drivers will automatically start after hitting the “Next” option. You will see the installation screen will appear one after another in the LCD Screen of the Computer.

Method 3: Finish and Restart

After completing the configuration process, you need to now do the following steps to finish the installation process in Windows.

  1. Tap on the “Finish” button. This will restart the device. After restarting the device, check if you have logged in with administrative rights.
  2. Now, “check for the Firmware Updates” page will appear on the screen. Select the “firmware update settings” option and then tap on the “OK” button. 

After following the above steps you will be able to complete the installation process. Now, you have successfully installed the drivers on the device. Try to take a print out and check if you are able to use your printer wirelessly or not. 

Final Note 

By now, you should be able to set up your Brother MFC 225CW by following the instructions as provided. In case you are facing any issues, then you need to consult a professional technician to help you out with the installation process. They will either guide you through the entire process or do it for you. 

07Dec/19

Brother MFC 8690DW Wireless Setup| Quick Installation Guide

Brother MFC 8690DW Wireless Setup

After buying a new Brother MFC 8690DW printer, you have to set up the router properly to carry out your printing jobs. You can set up this printer in two different ways, either by using USB or the wireless network. 

To set up the printer wirelessly, you must have some basic idea about the installation process. 

How to Proceed with Brother MFC 8690DW Wireless Setup? 

Here, you will know some easy steps through which you can set up your newly purchased Brother MFC 8690DW printer easily.

Step 1: 

First, unpack the printer device and check all the components properly. Install the toner cartridges and drum unit, which comes along with the printer.

Step 2: 

Load the pages in the paper tray of the printer and release the scanner lock. Afterward, connect the telephone line and the power cable. Also, attach the power cable to the electrical supply and turn on the device. 

Step 3: 

Select your preferred language and then choose the correct Receive Mode. Next, set the Date and Time after settings the LCD contrast. 

Step 4: 

Afterward, set the Station ID and Fax Transmission Report. Next, you will get the option to set the pulse or tone dialing mode. 

Now, you are ready to configure the wireless settings of the brother printer. 

Steps to Configure the Wireless Settings on Brother MFC 8690DW Printer 

Before implementing the below-discussed steps, you have to note down certain things for further usage: 

  • Network Name (SSID/ESSID). 
  • Network Key (Encryption Key, Password).
  • Encryption Mode (CKIP, AES, TKIP, WEP, None). 
  • Authentication Method (LEAP, EAP-FAST, WPA-PSK, WPA2-PSK, Shared Key, Open System).

You can find these items from the documentation provided with the wireless router. Most of the time, the Network Name could be the model or the brand name of the router. 

If you don’t know the security information, then you can consult your network service provider for details. Now, you can follow the below steps to configure the wireless settings of your Brother MFC 8690DW printer. 

Step 1: 

In the beginning, press the Menu key from the Control Panel of the Brother MFC 8690DW printer. Afterward, select the ‘Network’ option by using the Up/Down tab and press the OK button. Next, choose the ‘Setup Wizard’ option and press the OK button once again. 

Step 2: 

Now, it will start to search for the available SSIDs. So, select the Network Name that you have noted down earlier. Press the OK button to proceed further. If the Network Name is not listed here, then you can enter that manually. Thereafter, choose the ‘Infrastructure’ option and press the OK button. 

Step 3: 

Now, select one of the options below by using the Up/Down arrow key. 

 

  • No Authentication or Encryption: Select the ‘Open System’ option. Press the OK button and select ‘None’ for ‘Encryption Type’. Again, press the OK button and hit ‘1’ to apply the changes. Now, navigate to step 8.
  • No Authentication with WEP Encryption: Select the ‘Open System’ option. Press the OK button to continue. Afterward, select ‘WEP’ as ‘Encryption Type’ and tap OK. Now, navigate to step 4.
  • Authentication with WEP Encryption: Select the ‘Shared Key’ option and press the OK button. Next, navigate to step 4. 
  • Authentication with WPA/WPA2-PSK (TKIP or AES) Encryption: Select the ‘WPA/WPA2-PSK’ option and press OK. Now, navigate to step 5.
  • Authentication with LEAP: Select the ‘LEAP’ option and press the OK button. Afterward, navigate to step 6. 
  • Authentication with EAP-FAST/NONE, EAP-FAST/MS-CHAPv2, EAP-FAST/GTC (TKIP or AES Encryption): Select the ‘EAP-FAST/NONE, EAP-FAST/MSCHAP (EAP-FAST/MS-CHAPv2)’ or ‘EAP-FAST/GTC’ option and press the OK button. Now, navigate to step 7. 

 

Step 4: 

Afterward, select the appropriate key number and press the OK button. Type the WEP key that you have noted earlier. Press OK once again. Now, hit the ‘1’ button to confirm it. Then, navigate to step 8. 

Step 5: 

Choose the ‘AES’ or ‘TKIP’ option as ‘Encryption Type’ by using the Up/Down arrow tab and press the OK button. Next, type the ‘WPA/WPA2-PSK’ (TKIP or AES) password you noted down earlier.  

After entering the password, press the OK button and then press 1 to apply the settings. Now, navigate to Step 8. 

Step 6: 

Now, type the User Name and press the OK button to proceed further. Afterward, enter the Password and press OK. Press the 1 button to apply the changed settings. Now, navigate to Step 8. 

Step 7: 

Select the ‘AES’ or ‘TKIP’ option once again as ‘Encryption Type’ and press OK. Afterward, type the User Name. Press the OK button to proceed further. Next, type the password and press OK. Press the 1 button to apply the modified settings. Now, navigate to Step 8. 

Step 8: 

Your Brother MFC 8690DW printer will now try to connect to the broadcast network. If the connection is successful, it will display a ‘Connected’ message. 

Otherwise, repeat the steps 1-7 accordingly to do the Brother MFC 8690DW wireless setup.

07Dec/19

Brother MFC J270W Wireless Setup [Stepwise Guide]

Brother MFC j270w Wireless Setup

If you have just purchased a Brother MFC J270W printer for your personal use or office purpose, first, you need to set up the device to make it work. 

You can do this in two ways, using a USB and wirelessly. According to many users, it’s always better to set up the printer wirelessly. Hence, it is essential to have a proper idea to do Brother MFC J270W wireless Setup.

How to Setup Brother J270W with your Wireless Network?

Here, we have provided some simple steps through which you can set up the Brother J270W printer wirelessly. You can perform the steps as follows: 

  • First, unpack the printer and remove all the protective tapes. Afterward, load the paper properly into the paper tray. 
  • Now, connect the power cable and telephone line with the Brother printer. Next, install the ink cartridges and set the printing quality. 
  • Afterward, choose your preferred language by using the Up/Down arrow key. Next, select the correct ‘Receive Mode’. 
  • Now, set the contrast for the LCD of the device and set the ‘Date and Time’. After that, set the Station ID and check the fax transmission report.  
  • Thereafter, make sure the printer is having the tone dialing service. If you have Rotary or Pulse dialing service, then you need to change the dialing mode. 
  • Afterward, check the compatibility settings if you are connecting the printer to a VoIP service. 

After completing the above steps, you have to configure the wireless settings. 

How to Configure the Wireless Settings? 

Before you begin, check the broadcast network settings of the wireless router. Note down the Network Name and Network Key from the side or base of the router. 

Note: If you don’t find the Network Name and Network Key on the base or side of the router, then you can find them at the document that comes with the wireless router. 

Afterward, you can perform the steps given below: 

Step 1: 

Press the Menu button from the Control Panel of the printer. Choose the ‘Network’ option by using the Up/Down arrow key and press OK. 

Next, select the ‘Select Wizard’ and press the OK button. Afterward, you will see the ‘Enable WLAN?’ status at the display of the device. Accept it by pressing the OK button. It will start the broadcast setup wizard. 

Step 2: 

Now, it will start to search for the available SSIDs. After a few seconds, it will show a list of all the available SSIDs. Choose the Network Name that you have noted previously by using the Up/Down key. Press the OK button to continue. 

If you want to use the Encryption or Authentication method, it requires the Network Key. Hence, go to Step 3. But, if the Authentication method is ‘Open System’ and the Encryption mode is ‘None’, then go to Step 4. 

Step 3: 

Enter the Password or Network key that you wrote down earlier. After entering all the characters properly, press the OK button. 

Now, the Brother MFC j270W printer will try to connect with the broadcast network. However, it will take a few minutes to connect to the broadcast network. 

If you have followed the steps correctly, the wireless setup for the Brother MFC j270W printer is now complete. 

What to do if the Computer not Recognizing the Wireless Printer? 

If your computer is not recognizing the Brother MFC j270W printer, you can perform the steps provided below: 

  • First, press the Q and Win key simultaneously from the keyboard and type “printer” in the input field. 
  • Navigate to the ‘Printer & Scanners’ category. Thereafter, click on the ‘Add a printer or scanner’ option. 
  • Afterward, tap on the ‘The printer that I want is not listed’ option. 
  • Next, click on the ‘Add a Bluetooth, wireless, or network discoverable printer’ option from the next page. 
07Dec/19

Brother HL 3170CDW Wi-Fi Setup: [Step-by-Step Guide]

Brother HL 3170CDW Wi-Fi Setup

For basic home and office purposes, the Brother HL 3170CDW printer is a good choice as it offers fast and efficient printing. It can print both sides of the paper at once and can print upto 23 pages per minute. Moreover, you can use this printer through USB, Ethernet, and Wi-Fi. Here, we have provided the instructions for Brother HL 3170CDW wi-fi setup on a wireless network.

How to Setup Wi-Fi on Brother HL-3170CDW

Here we are going to provide some simple setup steps through which it will become easier for you to carry out the setup process. Before you start, make sure that you remember your router’s SSID and password. These are the same details that you use to connect to the Wi-Fi. 

Thereafter, follow the steps below. 

Step 1: 

First and foremost, unbox the printer and connect the power cable to it. Then, attach the power cable with the power supply and turn the device On. 

Step 2: 

Go to your printer’s Control Panel and press the Menu button. Thereafter, press the Down arrow until you see the ‘Network’ option. Then, select it by pressing the Ok button. 

Step 3: 

Again, press the Down button to navigate and select the ‘WLAN’ option. Once you find it, press the OK button to proceed further. 

Step 4: 

Lastly, navigate again and choose the ‘Wireless Setup Wizard’ to configure the printer’s wireless settings. Now, you will be prompted to enable WLAN for which you have to choose Yes to continue with the setup process. 

Step 5: 

After the previous step, the printer will now start searching for available wireless networks. Wait for a few seconds until the search completes. Afterward, you need to select your router’s SSID from the list and press the Ok button to connect to it. 

Step 6: 

Next, type the password of the Wi-Fi network by using the numpad keys. Select the characters by using the Down/Up arrow keys. Press the OK button to choose the character. After entering the password, press the OK button to continue. 

Step 7 

When you will see that the display is showing the ‘Apply Settings’ option. Press the OK button once again. Next, you will receive the Connected status at the LCD display. Now, you have successfully set up the Brother HL 3170CDW printer on the wireless network. 

Additional Information: People Also Ask

How to Print Using AirPrint on Brother HL 3170CDW Printer? 

Using AirPrint you can print directly from your iDevice. To do this, you can perform the steps as follows: 

  • First of all, make sure that the Brother HL 3170CDW printer is turned On and it is connected to a wireless connection.
  • Afterward, open the document that you wish to print. 
  • Tap on the Action icon and then tap on the Print button. 
  • Next, choose the printer. Here you will get the option to change the printing option if necessary. 
  • Lastly, tap on the Print button to print the document. 

Conclusion 

To summarize, your Brother HL 3170CDW printer should be able to connect to your home or office Wi-Fi after following the steps provided above. Thus, make sure that you have followed all the steps correctly. Thereafter, if you are unable to use your printer wirelessly, then you need to get in touch with an expert who will be able to guide you through the process in real-time. 

06Dec/19

Brother HL-3070CW Wireless Setup | [Complete Guide]

Brother HL-3070CW Wireless Setup

After purchasing a new Brother HL-3070CW printer, you need to set up the device to make use of its exclusive features. Hence, it is essential that you know how to set up the Brother HL-3070CW printer. 

How to Setup Wireless Brother HL-3070CW Printer? 

Here we are going to discuss the procedure to set up the Brother HL-3070CW printer easily. 

Before going to configure the broadcast settings, you need to get hold of the broadcast network settings of your wireless router. Check the Network Key (Encryption Key, Security Key, Password) and Network Name (ESSID, SSID) from the side or base of your router. 

If you are unable to locate the Network Key and Network Name at the base or side of the router, then you can check the documents that came with your wireless router. In most cases, the Network Name is the model name or manufacturer’s name.  

How to Configure the Wireless Settings? 

Now, you can configure the wireless settings by performing as follows: 

  • First and foremost, attach the AC power cable to the Brother printer. Connect it with the power supply and turn the device On. Afterward, turn the computer On. 
  • Insert the CD-ROM into the CD-ROM drive. The installation window will appear automatically. 
  • Select the model name from the list of printers. Afterward, choose your preferred language. 

Note: But if the installation screen doesn’t appear, then open the File Explorer and navigate to the  ‘This PC’ section. Next, open the DVD/ CD drive and click twice on the ‘start.exe’ file to open the installation window. 

  • Now, the CD-ROM main menu will open. Tap on the ‘Install printer Driver’ from the list. 
  • Next, click on the ‘Wireless Network Users’ option from the next screen. Tap on the ‘Yes’ or ‘Allow’ button from the ‘User Account Control’ window. 
  • Once it opens the ‘Windows Installation Type’ window, tick the box that prompts ‘Wireless Setup and Driver Install (Recommended).’ 

After performing the above steps, there are two options you can try. They are: 

Option 1: 

If you see that the ‘Temporary use a USB cable (Recommended)’ message appears on the next screen, select it and tap on the Next button to proceed further. Afterward, perform the steps mentioned below: 

Step 1: 

First, you have to make sure that you have the broadcast security information. Then, check the box that prompts ‘Checked and Confirmed’ and click on the Next button to continue. Now, connect a USB cable with the computer and the Brother printer. 

Step 2: 

Afterward, the broadcast settings will be detected by itself. Now, if you see the ‘Installation Confirmation’ screen appearing, confirm the information that is displayed and tick the ‘Checked and Confirmed’ box. Tap on the Next button. 

Now, the Network Name will be displayed. Click on Yes and then the Next button to continue. Next, go to Step 6. 

But, if you see that the ‘Available Wireless Networks’ screen appears, then here you will see a list of all the available wireless networks. Select the Network Name that you have noted down earlier and click Next. Afterward, go to Step 4.   

If the Network Name is not in the list of available networks, go to Step 3. 

Step 3: 

If the SSID or ESSID name is not on the list, then you have to confirm the following points: 

  • If the router is router is turned off, turn it On. 
  • If your printer is placed too far from the router, or if there is any obstruction, then place the printer as close to the router as possible with minimum obstruction.
  • The Brother HL-3070cw printer supports the IEEE 802.11g and IEEE802.11g network. Hence, you need to make sure that the router supports the IEEE 802.11g and the IEEE802.11g network and one of the networks is enabled. 
Step 4: 

If the ATTENTION page appears, then you need to configure the security settings of your router to prevent unauthorized access to the network. 

If you want to configure the security settings of the router later, tap on the Cancel button to close the Wizard. If you want to configure it now, tap on the OK button and go to Step 6. 

Step 5: 

Provide the Network Key that you have noted previously and tap on the Next button to continue. 

Step 6: 

Now, you have to make sure that the settings are correct. Afterward, tap on the Next button. It will send the settings to the printer. 

  • If you want to change the IP address, tap on the ‘Change IP address’ option. Then, set the new IP address manually. 
  • If you tap on the Cancel button, the settings will the disabled. 
Step 7: 

Once the ‘Disconnect Your Device and Your Computer’ screen appears, you can detach the USB cable from both the devices. Afterward, you will receive a confirmation message. 

Now, install the driver for the network connection to complete this procedure. 

Option 2: 

If you see the ‘Step by Step install (Recommended)’ message appears on the next screen, click on it and tap on the Next button to continue. Afterward, you can follow the steps given below: 

Step 1: 

Select the ‘With cable (Recommended)’ option from the next screen and then tap on the Next button to proceed further. Connect the printer to the access point using a network cable. Click on the Next button to proceed further. 

Step 2: 

Select the printer that you want to configure and tap on the Next button. If you see that the list is blank, you can check if the printer and the access point are powered On. Afterward, tap on the Refresh button to continue. 

Step 3: 

Now, the wizard will start searching for the available wireless networks. Select the access point that you want to connect with the printer. Tap on the Next button. 

Step 4: 

If the ATTENTION window appears, then configure the security settings of the router to prevent unauthorized access to the network. 

If you wish to configure the security settings of the router, tap on the Cancel button. Else, click on the OK button and go to step 6. 

Step 5: 

If the network is configured for Encryption and Authentication, the ‘Authentication Method and Encryption Mode’ window will open. While configuring the printer, you need to match the Encryption and Authentication settings that you have noted down earlier. 

Select the Encryption Method and Authentication Method from the drop-down box. Then type the Network Key and tap on the Next button to continue. 

Step 6: 

Now, insert some papers into the paper tray of the printer. Confirm that the settings are correct and tap on the Next button. Now, the printer will print the network configuration page. 

  • If you want to change the IP address, click on the ‘Change IP Address’ option to do that. 
  • If you click on the Cancel button, the settings will be disabled. 
Step 7: 

Select the ‘Link Ok’ status from the ‘Wireless Link Status’ section and click on the Next button. Now, you can disconnect the network cable from both the devices. 

Once you get the confirmation message, install the driver for the network connection and complete the installation process by following the on-screen guidance. 

Congratulations!  If you have followed the steps accurately, you have successfully set up the Brother HL-3070CW printer wirelessly. 

06Dec/19

Brother MFC J410W Wireless Setup: A Quick Guide

Brother MFC J410W Wireless Setup

Currently, Brother All-in-one printers have become popular for both office and home purposes. Out of these, the Brother MFC-J410W printers are the most bought printer by many users. One of the main features of this printer is its Wireless connectivity. Thus, it allows users to print without a wired connection. Thus, you need to know how to setup a brother mfc-j410w wireless printer.

Effective Methods to Setup Brother Mfc-j410w Wireless Printer 

In this section, we are going to provide detailed methods to help you set up your printer wirelessly. Thus, go through these one by one. 

Method 1: Configure Printer’s Wireless Settings

The first thing you need to do is to configure wireless settings from the printer’s control panel. Thus, follow the steps below to perform this task.

  1. Firstly, you need to go to your printer and open its Menu. Thereafter, press the ‘6’ button to open the Network. 
  2. Next, press the ‘2’ button to head over to WLAN. After selecting this, the device will ask for confirmation regarding enabling WLAN. Thus, press the ‘1’ button to confirm this change. 
  3. Now, this will start the Wireless Setup Wizard. Thereafter, it will search for available wireless connections within the area. 
  4. Thus, select your router’s SSID and press the Ok button to go to the next menu. 
  5. Finally, enter your router’s password and finish the setup process. The printer will automatically connect to this wireless network every time it is turned on. 

If you failed to establish a connection, then you need to repeat all the steps once again. After establishing the wireless connection, you need to now install the printer driver to properly connect your printer. 

Method 2: Install Printer Drivers

After connecting the printer and Wifi, you need to install the printer drivers. Generally, you can get the printer driver software along with the device itself. Alternatively, you can download the latest version from Brother’s official website. 

Therefore, follow the steps provided below to carry out the installation procedure.

  1. Firstly, insert the CD-ROM or run the driver installer downloaded from the Internet. Now, select the model of your printer from the menu and click Next. 
  2. Now, select the “Wireless Network connection” option and click on Next once again. 
  3. After that, you will be prompted to either Change the firewall settings or to continue with it. Here, choosing the “Change firewall settings” is recommended. 
  4. Next, follow the instructions as provided on the screen to carry on with the installation process. Also, make sure that your computer is connected to the printer through USB or LAN connection. 
  5. Finally, follow the rest of the instructions to complete the setup procedure. Thereafter, print a test page to check whether you are able to use your Brother MFC J410W printer wirelessly or not. 

Conclusion

To summarize, you should be able to print wirelessly by following the steps provided in the above section. Thereafter, if you are facing any issue during printing, then you need to check for the following points.

  • Check if the ink cartridge has sufficient ink
  • Set the paper in the tray property.
  • Make sure the trays of the printer is properly placed.
  • Check if you have put the paper in the correct tray.